行业新闻
  • 您现在的位置:首页 > 新闻资讯 > 行业新闻 >
  • 一般实验台安装要注意什么?
    来源:http://www.jnyhrs.com 浏览: 发布日期:2021-10-08
    1、所有实验台底柜应独立完整,左右双门柜应该是开放式的,不应设置中间支撑列以避免影响项目的访问,落地式底柜必须配备钢制调节脚和底柜,下缘距离地面的高度应大于10mm;
    1. All the bottom cabinets of the test bench shall be independent and complete, the left and right double door cabinets shall be open, and the middle support column shall not be set to avoid affecting the access of the project. The floor type bottom cabinet must be equipped with steel adjusting feet and bottom cabinet, and the height from the lower edge to the ground shall be greater than 10mm;
    2、所有钢制柜和框架应经过良好和完整的耐酸碱环氧粉末烘烤工艺,烤漆成品膜平均厚度在75米以上;
    2. All steel cabinets and frames shall undergo good and complete acid and alkali resistant epoxy powder baking process, and the average thickness of finished paint film shall be more than 75m;
    3、实验台各单元底柜的门板和抽屉应便于更换,无任何障碍;
    3. The door panels and drawers of each unit bottom cabinet of the test bench shall be easy to replace without any obstacles;
    4、每一相邻底柜的型式和高度相同的门和抽屉应在同一中线,不应因加工不良而造成,中间线之间的间隙应在3.175 mm(1≤8)以内;
    4. Doors and drawers with the same type and height of each adjacent bottom cabinet shall be in the same center line, which shall not be caused by poor processing, and the gap between the middle lines shall be within 3.175 mm (1 ≤ 8);
    济南沙发维修
    5、检查实验台外侧的所有开口,所有开口都插有适当的插头;
    5. Check all openings on the outside of the test bench, and all openings are plugged with appropriate plugs;
    6、用环氧树脂粘结剂代替硅胶粘接试验台上所有环氧树脂台面,硅胶可用于将防水背板与台面粘结在一起,以美观,每个接缝处的缝隙宽度不应超过3.175mm(1/8),接缝台面应平整且不不平;
    6. Use epoxy resin adhesive instead of silica gel to bond all epoxy resin table tops on the test bench. Silica gel can be used to bond the waterproof back plate with the table top for beauty. The gap width at each joint shall not exceed 3.175mm (1 / 8), and the joint table top shall be flat and not uneven;
    7、实验台的面板应尽可能保持完整,接头应尽量减少,不要垂直连接;
    7. The panel of the test bench shall be kept as complete as possible, and the joints shall be reduced as far as possible without vertical connection;
    8、检查实验台面外缘以下是否有沟槽,沟槽应采用凹形加工,而不是隆起型;沟槽的宽度应不小于2mm,深度不应小于3mm,沟槽的宽度不应小于2mm,沟槽的深度不应小于3mm;
    8. Check whether there are grooves below the outer edge of the test table. The grooves shall be concave rather than raised; The width and depth of the trench shall not be less than 2mm, 3mm, 2mm and 3mm respectively;
    9、检查水,电,气和风管的位置和界面,检查设计是否有偏差,并及时将信息反馈给项目经理,项目经理与业主或其他承包商沟通,以确定更终解决方案;
    9. Check the position and interface of water, electricity, gas and air ducts, check whether there is any deviation in the design, and feed back the information to the project manager in time. The project manager communicates with the owner or other contractors to determine the final solution;
    10、根据图纸布置底柜,同一试验台的所有机柜将在同一水平面上的安装位置设置(绝对禁止在不调整水平面的情况下增加垫片和其他物品),水平调整后,底柜与底柜的间隙距离不应超过1 mm,接头上下误差不应超过0.5 mm,如果所有的柜子都需要连接在一起,则必须在调整好水平后再连接,连接时,接头处均匀密缝的距离不得超过0.7mm,上下接缝的误差不得超过0.5mm。
    10. The bottom cabinet shall be arranged according to the drawing. All cabinets of the same test bench shall be set at the installation position on the same horizontal plane (it is absolutely forbidden to add gaskets and other items without adjusting the horizontal plane). After horizontal adjustment, the gap distance between the bottom cabinet and the bottom cabinet shall not exceed 1 mm, and the up-down error of the connector shall not exceed 0.5 mm. If all cabinets need to be connected together, It must be connected after adjusting the level. During connection, the distance between uniform and close joints at the joint shall not exceed 0.7mm, and the error of upper and lower joints shall not exceed 0.5mm.